Search results

wait another couple of weeks .if Gm is going to make them the yshould by the end of the month .if not once the ydiscontinue the part number we have alternatives. But no use working on those if GM makes more of the part. i orderer 40- 50 I forget and they shipped the last three they had so with...

no just picked up a used one I happen to see in a lot. I think It was off a coupe let me look this weekend and see if it has a number on it

the above fasteners are interior trim Asian and fit into a plastic or metal clip that actually has the teeth on the receiver clip to bite into the groves of the fastener shown In the box above. they will not hold when pressed into a steel hole. Takes a Christmas tree type and the best place...

you would be giving up ride, performance, handling extra wear on parts etc. 3 inches would be whole lot .that would put extra stress on the front leaf spring. Its set up for ride height to be in the middle of its up and down movement. I also doubt if you could align the camber either would...

I mounted one off of a Saturn on my center section. its spring loaded. hit something and bong!!! its right back into place. ( not a direct fit) haha

could have got 2 for 27 on ebay also with free shipping. haha . Only reason we have these is because they fit the Vette or we would have another part unavailable.

you should only adjust one bolt at a time. Loosen the rear first. then pick up on the hood .that will lower the rear. tighten it and then loosed th front. pick up on the hood that will raise the front of the hinge and lower the rear. loosening both at the same time will allow the whole hinge...

IAn what are you talking about. continue to look all you want. Others have been doing it for over 4 years now since the headlights became so costly. I just started looking about 3 years ago and made a paper template that I took with me. Every time I saw a car that looked close I would check it...

rattles and water leaks can drive you batty and are so simple to fix once you find them but it can take a lot to locate it. I would have guessed inside the cat but they usually sound like marbles rattling around when they start to go. got nothing on this one. sorry

we had a post on here or the other forum with about 200 lights that "look" the same and no were near fit. These where on there. 2 or 3 people went to keystone and unboxed every light that appeared to be close and photographed some of them . I would love to see one that would be close. Just...

did the second one also have damage? I wondered why you mentioned a third? Gm parts from warehouse to dealer are handled pretty well. Its when they don't repack and ship as received by fedex etc that they get damaged. Drivers door hinges are available and will most likely be for a while as they...

apparently this. haha I have not seen one leak either. The corvettes use the same ones or at least the same style and I was correct above. some guys said they did theirs in an hour .looks like they like to replace them with a more solid bushing type. I will have to look but the aluminum mount...

read the corvette forums the guys that replaced their z06 shocks with bilsteins did not notice any difference unless they went with the comp shocks and had the car lowered. springs changed and wheels upgraded to wider. really depends on how hard you drive the car and if you have upgraded...

that's pretty strong money. that's time is almost engine removal and replacement time. the studs do look a little long on the mounts which run 20-40 each. its going to be a combo of blocking the engine then letting the car down a bit plus loosening the crossmember one side at a time to wiggle...

that was me on ebay .I ordered two and he pulled them. Ebays rules say they cannot sell if they dont have an item but they do

I was looking for the one that closely matched ours but have not found my notes. Once the dealer told me they had them I stopped looking . then he told me they had three. hahaha I sent you a pm

all of them will tell you they know how to do it. Be careful as it can cost you if they don't.

just buy the stock z06 Corvette shocks. you can get a set of take offs with no miles on them on ebay for 400$ and the sims for 200 .Add a sway bar for 125 and your ride will be as good to better than it ever was when new. I just road in a car with brand new Mags on it and it did not ride a bit...

actually GM still showed them in stock a month or so ago so I ordered 40 of them and they shipped 3. They have not discontinued the part number yet so my parts guy says I should get them some time before the end of the month. It would be good to have a backup plan if they don't make any more...

old thread but people are still looking for these. the above number is for the magnet not the VVT itself. 12613455 is no longer made and Dorman the only company making them has no date in sight for new ones. I have a nice collection of used ones and 3 GM factory ones should anyone need any